Pump starters
Greenly automatic starter panels protect the motor from dry running, overload and voltage problems, and control tank levels.
Learn moreIrrigation systems
Irrigation automation
Protected cultivation
Landscapes & green spaces
Pump starters & controllers
Drip automation
Water level & tanks
Product ranges
Products
Starters, GSM pump controllers, drip automation units, sensors and level controllers made by Greenly, plus the components for complete drip, sprinkler and mist systems.
01
Greenly automatic starter panels protect the motor from dry running, overload and voltage problems, and control tank levels.
Learn moreGreenly panel pump controllers mount in the pump panel and protect single-phase submersible pumps from dry running, overload…
Learn moreA preventer protects three-phase motors from single phasing, reverse phase and voltage problems, the commonest causes of…
Learn moreIn many rural areas three-phase power is available only for part of the day.
Learn moreGreenly 3010 series three-phase controllers start and stop the pump by top and bottom tank levels, and protect it from low…
Learn moreSwitch your pump on and off from anywhere with a Greenly GSM controller.
Learn moreThe 3010 GSM Double BSD controls two three-phase pumps from your phone over 4G and GPRS, and reports site voltage, pump load…
Learn moreGreenly timers switch pumps, valves and lights on programmed cycles or at set clock times, and on-delay timers set…
Learn moreGreenly cyclic/RTC timers with 4 or 6 relays switch compressors, air valves and other loads in sequence or on programmed…
Learn moreGreenly builds irrigation control panels to suit each customer: single-phase mobile starters and controllers, automatic…
Learn more02
Greenly valve controllers switch the motor and the solenoid valves on and off together, so each drip zone runs in turn.
Learn moreWhen valves are far from the motor room, Greenly wireless nodes operate them without cable: a transmitter at the controller…
Learn moreGreenly electric actuators automate small ball valves, plug valves and dampers, so manual valves can be opened and closed by…
Learn moreA Greenly fertiliser controller releases fertiliser into the irrigation water at a set rate, per valve or crop, so nutrients…
Learn moreThe Greenly flow meter measures how much water goes into the irrigation pipes, so the controller can give each valve an…
Learn moreFiltration is essential in any drip or micro-sprinkler system, because emitters clog easily.
Learn moreGreenly pressure devices measure and control pressure in the irrigation network: pressure sensors report to the controller…
Learn moreA pressure relief valve releases water when line pressure rises too high, protecting pipes, joints and emitters from…
Learn moreSensors tell the controller what is happening in the field and the tank.
Learn more03
Greenly makes IoT-based water level monitors and automatic level controllers.
Learn moreThe transmitter sits on the tank and the receiver shows the level indoors, with no cable between them.
Learn moreGreenly wireless tank controllers send the tank level to the pump by radio, so there is no cable to lay between the tank and…
Learn moreThe Greenly wireless transmitter and receiver work as an automated irrigation control and security system.
Learn moreSimple, low-cost alarms: the pipe line alarm rings when water starts coming through the supply pipe, and the tank full alarm…
Learn more04
Greenly makes the controllers that automate irrigation and water supply: GSM pump controllers you can operate by call, SMS…
Learn moreGreenly IoT irrigation products monitor field conditions such as light, humidity, soil moisture and temperature, and let…
Learn moreDrip irrigation applies water slowly, at 2 to 20 litres an hour per emitter, through small-diameter pipes fitted with…
Learn moreSprinkler irrigation applies water like rainfall through pipes, risers and nozzles.
Learn moreEverything needed to build a misting system for agriculture and horticulture: high-pressure misting pumps, nozzles, tubing…
Learn moreGreenly supplies equipment for the main hydroponic methods: wick systems, deep water culture, nutrient film technique (NFT)…
Learn moreGreenly supplies the accessories that complete a drip or automation system: automatic solenoid valves, compressor air…
Learn moreCatalogue
Order spares and individual controllers from the product catalogue.



































FAQs
Match the starter to the motor and the supply at the pump. Single-phase models suit motors up to about 3 hp on a 230 V supply; three-phase and 1/3-phase models suit larger agricultural pumps. If your area gets only two phases for part of the day, ask for a 1/3-phase (2 & 3 phase) model.
It switches the motor off when the pump is running without water, which happens when a borewell or sump runs low. Running dry overheats the pump and damages seals and windings. Most of our starters also restart automatically after a set time.
The crop, the area and plot shape, the water source and pump details, and a location pin. With these we can prepare a layout and an itemised quotation; a site visit confirms the final design.
Yes. We design the mainline and valve positions so that solenoid valves, a controller and sensors can be added later without replacing the pipe network.
From requirement to quotation
Share the crop or site, the area, the water source and your pump. We reply with the right system and an itemised quotation.
Talk to an irrigation engineer
Not sure which system fits your farm or site?